Legend Fitness Strength Equipment Specifications

Frame Materials:

All steel components are machined to a minimum of +/- .030"e;

Construction is primarily of Square Tubing 3"e; x 11g, Rectangular Tubing 4"e; x 2"e; x 11g and Rectangular Tubing 3"e; x 2"e; x 11g and a combination of other heavy structural tubular steel sizes with an ASTM rating of A500 grade (minimum mechanical properties of 58,000 PSI tensile strength and 46,000 PSI yield strength).

Weight Stacks:

75 lb. weight stack in 5 lb. increments.--Neck machine

170 lb Weight Stack--Pec Deck - Rear Delt - Arm Curl - Tricep Extension - Leg Curl - Cable Crossover - Ab Crunch

200 lb Weight Stack--Chest Press - Shoulder Press - Lever Lat - Lat - Seated Row - Leg Extension - Leg Extension /Curl Combo - Dip /Chin - Tricep Dip - Lat / Seated Row Combo

320 lb Weight Stack--Standing Calf - Low Back - Leg Press - Seated Leg Press


Features all-welded construction by inert-gas MIG welding to conform with and in accordance with the following codes and/or standards: 3:1 AWS, A3.0 Welding Terms and Definitions 3.2 AWS D1.1-81 Structural Welding Code-Steel 3.2 AWS D9.1 Specifications

Frame Finish:

Each piece of equipment is prepared both mechanically and chemically for powder-coating. This process includes a high-temperature, high-pressure iron phosphate wash to ensure optimum adhesion of the electrostatically applied TGIC polyester powder. This is an engineered powder that is scuff resistant and long wearing. The finished is then baked at 400 degrees Far. and carefully monitored to ensure complete curing.

Technical summaries are determined using 3.0 - 5.0 mil powder film over iron-phosphated, pretreated steel using and conforming with the following test methods:

ASTM B5965-96, C

ASTM D 3451-93, 13

UL DTOV2 organic coatings

Padding and Upholstery:

The padding material is 2"e; thick rebond foam meeting ASTM 1692 and MVSS302 standards for flammability. Foam density is 8 lbs. per cubic foot. Upholstery is 32 oz. Sulfide-stain resistant "e;Naugahyde"e; formulated to meet small scale flammability test requirements contained in Federal Standard 191A (CCC-A-680 a). All pads are top double-stitched. Foam is glued to a 3/4"e; thick support board, then trimmed to fit exactly. Corners are radiused and edges are chamfered on both top and bottom to promote comfort and durability.


Input and movement arms rotate with either non-friction roller bearings with a Basic Radial Load Rating of 2420 pounds, contained in a custom cast and machined housing or a self-lubricating bronze bushing in a machined steel housing to provide smooth movement and precise alignment.

Weight Transport:

1/4"e; diameter aircraft cable with a 7 x 19 construction and black nylon coating. the cable is rated at a breaking strength of 4200 lbs.


Pulleys are 4 1/2"e; diameter fiberglass-impregnated nylon with a precision fit cable groove and 6203 double sealed non-friction roller bearings.

Weight Plates:

All Legend selectorized equipment features solid cast-iron weight stack plates with a black finish. Self aligning low friction sleeve bearing surround the guide rods on every weight stack plate.

Spring Suspension:

Heavy duty die cast springs are used under the weight stack to reduce shock and vibration stresses.

Guide Rods:

Guide rods are solid steel and hard chrome plated to ensure quiet operation and low friction movement.

Linered pins:

All Legend selectorized equipment features weight stack pins that are linered with a coiled self-storing cord to prevent pin removal or loss.


All bolts meet ANSI B18.3 specifications.


45 durometer rubber handgrips are used for comfort, safety and durability.


Legend Fitness Systems warrants to the original purchaser only that Legend equipment will be free from defects in material and workmanship under normal use and service. This warranty does not cover upholstery or products not manufactured by Legend or products which are altered. This warranty will expire in ten years from the delivery date to the original purchaser for any welds covered by the warranty and will expire in one year from the date of delivery to the original purchaser all other warranted parts. The obligation of Legend under this warranty is limited to repairing or replacing warranted defective parts, as Legend may elect. Purchaser is responsible for all transportation cost to and from manufacturing plant. The remedy of repair or replacement is the exclusive and sole remedy of the purchaser. Legend shall not be liable for any special, incidental, contingent or consequential damages of any kind, including but not limited to, damage or loss of other property, equipment and loss of profits or revenue. Contact Legend before returning any defective parts. This written warranty is the complete, final and exclusive agreement of the parties with respect to the quality or performance of the goods and any and all warranties and representations.

Have additional Legend Fitness technical questions or need a Legend Fitness quote? Call an Ironcompany certified strength equipment representative at 1-888-758-7527.